buy 1045 hardness Related introduction

  1. AISI 1045 Carbon Steel - AISI 1045 Medium Carbon Steel ...

    C1045 is a medium carbon, medium tensile steel supplied as forged or normalized. This steel shows reasonable strength and toughness. C1045 will through harden to 2.5 (63mm) with a tensile strength of 66-120 Ksi (620-850 MPa). Contact All Metals & Forge Group for your forging needs.

  2. AISI 1045 Steel, SAE-AISI 1045 (S45C, G10450) Carbon ...

    AISI 1045 steel has a low through-hardening capability that recommended for tempering and through-hardening. Carbon steel AISI 1045 is a medium carbon, medium tensile steel supplied as forged or normalized. This steel shows reasonable strength and toughness. 1045 is the designation in both the SAE and AISI systems for this material.

  3. 1045 Medium Tensile Carbon Steel Bar, Interlloy ...

    1045 is a medium tensile low hardenability carbon steel generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 - 700 Mpa and Brinell hardness range 170 - 210 in either condition.Characterised by fairly good strength and impact properties, plus good machinability and reasonable weldability in the hot rolled or normalised buy 1045 hardness

  4. ASTM SAE AISI 1045 Carbon Steel Heat Treatment, Chemical ...

    The austenitizing temperature for SAE 1045 induction hardening carbon steel is 800-845 °C. Full Annealing. The annealing temperature for AISI 1045 carbon steel is from 790-870 °C, cooling cycle from 790 to 650 °C at a rate of 28 °C/h in furnace, and can get the HBW hardness range from 156 to 217.

  5. Keyed Shafting 1045 Key Shaft, Buy Online! Metals Depot®

    1045 Pre-Keyed Precision Ground Shafting, is a 1045 steel round that has been turned, ground and polished to a 32 RMS surface finish with a pre-machined full length keyway cut to ANSI standards.Pre-keyed shafting is an economic alternative to machining

  6. Buy Cold Roll Round Bar 1045 Online - onlinemetals.com

    Buy cold-roll-round-bar-1045 and other metal-working products online at OnlineMetals.com.

  7. 1045 Cold Rolled Steel Turned, Ground & Polished Round Bars

    1045 Cold Rolled Steel Turned, Ground & Polished Round Bars. WORKABLE: This is medium-carbon steel.The higher content imparts higher strength properties than 1018 steel. When higher degrees of dimensional accuracy and straightness are required, we recommend the use of PRECISION SHAFTING.

  8. Buy High Carbon Steel: 1045, 1050, 1055, 1060, 1070, 1075 ...

    Blue Blade Steel offers the highest quality high carbon steel AISI/SAE 1045, 1050, 1055, 1060, 1070, 1074, 1075, 1080, 1085, 1090, 1095 and C67S strip coil. Sometimes referred to as clock spring steel, or scaleless blue steel, our high carbon pretemp spring steel

  9. Speedy Metals - 1045 Plate Steel Sheet and Plate

    1045 Steel Sheet and Plate. Typical Applications. 1045 hot roll plate has a wide variety of applications. It is used for machinery parts, excellent for die forging and hot upsetting, gears, bolster plates, base plates, wear plates, brake dies etc. 1045 hot roll plate can be flame cut to various shapes for a multitude of uses, both in the hardened or annealed condition.

  10. AISI 1045 Medium Carbon Steel - AZoM.com

    See more on azom.comSome results are removed in response to a notice of local law requirement. For more information, please see here.

  11. 1045 Cold Rolled Steel Turned, Ground & Polished Round Bars

  12. MEDIUM TENSILE STEEL AISI 1045 - S&T Stainless

    MEDIUM TENSILE STEEL AISI 1045 AISI 1045 Medium Carbon, Medium Tensile Steel, supplied black as rolled, black as forged or normalised and bright drawn or smooth turned, offering good strength, toughness and wear resistance. Will through harden in sections up to 63mm with a tensile strength of 620 - 850 MPa. TYPICAL APPLICATIONS:

  13. 1045 steel hardness - alibaba.com

  14. 1045 MEDIUM TENSILE CARBON STEEL BAR -

    1045 is a medium tensile low hardenability carbon steel generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 - 700 Mpa and Brinell hardness range 170 - 210 in either condition.Characterised by fairly good strength and impact properties, plus good machinability and buy 1045 hardness

  15. Atlas 1045 Medium Tensile Carbon Steel Bar 1045

    Atlas 1045 black round bar is supplied with max. dimensional tolerance on diameter of ±1.5% (min. 0.4mm). Atlas 1045 cold drawn/turned round bar is supplied in tolerance h10 or h9. Atlas 1045 centreless ground round bar is supplied in tolerance h8 or better. Atlas 1045 square bar, hexagonal bar and flat bar are supplied in tolerance h11.

  16. ASTM SAE AISI 1018 Carbon Steel Chemical Composition ...

    Below is material AISI 1018 carbon steel datasheet including chemical composition, density, thermal expansion coefficient, thermal conductivity, yield strength, hardness, etc. AISI SAE 1018 Chemical Composition. ASTM AISI SAE 1018 chemical composition is presented in the following table.

  17. Metals Depot® - 1045 TGP Steel Round Shafting

    Buy 1045 TGP Shafting Round Online at MetalsDepot - America's Small Quantity Store. Huge selection of steel round, stainless round, and aluminum round. Any Quantity, Any Size, Delivered Anywhere!Some results are removed in response to a notice of local law requirement. For more information, please see here.

  18. Carbon Steel Grade 1045, Elgin Fasteners

  19. MEDIUM TENSILE STEEL AISI 1045 - S&T Stainless

    MEDIUM TENSILE STEEL AISI 1045 AISI 1045 Medium Carbon, Medium Tensile Steel, supplied black as rolled, black as forged or normalised and bright drawn or smooth turned, offering good strength, toughness and wear resistance. Will through harden in sections up to 63mm with a tensile strength of 620 - 850 MPa. TYPICAL APPLICATIONS:

  20. AISI 1045 Steel, cold drawn, high temperature stress ...

  21. Atlas 1045 Medium Tensile Carbon Steel Bar 1045

    Atlas 1045 black round bar is supplied with max. dimensional tolerance on diameter of ±1.5% (min. 0.4mm). Atlas 1045 cold drawn/turned round bar is supplied in tolerance h10 or h9. Atlas 1045 centreless ground round bar is supplied in tolerance h8 or better. Atlas 1045 square bar, hexagonal bar and flat bar are supplied in tolerance h11.

  22. AISI 1045 Carbon Steel (UNS G10450) - azom.com

  23. Mechanical Properties of Steel - Pivot Point

    Mechanical Properties of Steel - Condition, Strength, Hardness, Machinability. Stainless Steels. AISI. Type 302 HQ Type 303. Type 304 Type 316. Type 410 Type 416. Type 17-4 Materials. Condition Annealed Bars. buy 1045 hardness 1045. 1212 12L14. 1215 1117. 1141 1144. Type of Processing. Hot rolled Cold drawn. Hot rolled Cold drawn.

  24. Flame hardening 1045 steel - practicalmachinist.com

    Jul 15, 2011 · with 1045 and 1060. The big rosebud managed to get the whole surface up to temp ( judging by color and the magnet ). Again this was not a real important part. I don't have a hardness tester but can report that a plain old HSS 1/8th in drill bit won't cut into it on the hardened surface but will still drill the back side. Polished them off with buy 1045 hardness

  25. Carbon Steel 1050 Rolled Metal Products, Stainless ...

    Rolled Metal Products is one of the steel industrys most respected service centers with facilities across North America. We stock Stainless Steel, Nickel Alloys, Aluminum and other Specialty Metals in coil form and also offer toll processing of various metals including: Stainless Steel, Nickel Alloys, Titanium, Aluminum, Brass, Copper, Carbon Steel, and other Specialty Metals.Some results are removed in response to a notice of local law requirement. For more information, please see here.

Online Consultation